I've tried this on both Windows XP and Windows 2000, and it has worked:[/B]


1. Click on "Start" in the bottom left hand corner of screen
2. Click on "Run"
3. Type in "command" and hit ok

You should now be at an MSDOS prompt screen.

4. Type "ipconfig /release" just like that, and hit "enter"
5. Type "exit" and leave the prompt
6. Right-click on "Network Places" or "My Network Places" on your desktop.
7. Click on "properties"

You should now be on a screen with something titled "Local Area Connection", or something close to that, and, if you have a network hooked up, all of your other networks.

8. Right click on "Local Area Connection" and click "properties"
9. Double-click on the "Internet Protocol (TCP/IP)" from the list under the "General" tab
10. Click on "Use the following IP address" under the "General" tab
11. Create an IP address (It doesn't matter what it is. I just type 1 and 2 until i fill the area up).
12. Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers.
13. Hit the "Ok" button here
14. Hit the "Ok" button again

You should now be back to the "Local Area Connection" screen.[/B]
15. Right-click back on "Local Area Connection" and go to properties again.
16. Go back to the "TCP/IP" settings
17. This time, select "Obtain an IP address automatically"
18. Hit "Ok"
19. Hit "Ok" again
20. You now have a new IP address

With a little practice, you can easily get this process down to 15 seconds.

P.S:
This only changes your dynamic IP address, not your ISP/IP address.

 

 

 

Reply

hmm...i dunno if I changed my dynamic IP address or what...but my router lets me change my ip address as well and it takes much less effort then your technique =P

just a note: i think it would be wise to type "ipconfig /renew" in the command prompt window (cmd) after the last step...cause some computers wouldn't make the change without first renewing it... ^_^

Reply

Did you steal that or did you make it up, that is the question.
I reccomend you talk to an admin, me, and talk about putting some graphics in that, and uploading it to the server as a word document.

Reply

so basically, you are restarting the network and hopeing that the DHCP server gives you a different IP address....

so.... the question arises.. why would you want to do this ?
this is about as usefull as changing the colour of your kidneys.

Reply

well, i'm not sure of why the topic starter would...but personally i have to change to a differerent ip address then change back because a certain server doesn't allow to connect to them *cough*ezboard*cough*. But actually recently I haven't found a need to do that...cause i left ezboard and all their stupid glitches

Reply

does it work for dynamic ip's though? (dynamic is like cable or dsl...right?...or is that static.....) ive been told before by people that ip changing can only be done by your isp

Reply

i think that will only change ur dynamic IP address
if u wan to change the ISP/IP address i think u will need to reconnect to the internet
sometimes some ISP will provide a fixed IP for u .. so u cant even change it

Reply

You can't change it ?

Reply

Does this enable you to get to sites that you have been blocked because you are using a proxy?

Reply

if you have a very very small network, you can use manually assigned IP addresses, and yes, change them.

however on normal networks, a DHCP server sets your IP address.
in this case, to change your IP, you need to own the DHCP server.

on the internet, the DHCP server is owned by your ISP.
they MAY keep your IP static, but they dont have to...

usually, they will assign you whatever ip address is free when you connect ot the internet... so dissconecing your cable modem (unplugging from power) and then re-starting it means your ISP's DHCP server MAY give you a different IP.. however iyou have no controll over what IP they assign you.

and if your IP is blocked by some online server, use a PROXIE !!!

i hereby declair this thread, and infomration contained therein, obsolite.

Reply